MIROBILD AC Acid Catalysed Lacquers

Code: 3750 A high solids, pigmented, acid catalysed topcoat. Features: High build, ehances the finished appearance by providing maximum build with the minimum number of coats Bright white and low yellowing which minimises discolouration of light coloured coatings Excess MIROBILD AC 3750 topcoat may be added into MIROBILD AC 3720 undercoat. This improves coverage and reduces waste Specifications: Colour : White & Colours as requested Finish : Satin (30%), Semi Gloss (60%) & Full Gloss Build : Excellent Sandability : Excellent Vertical Hold Up : Excellent Solvent Resistance : Excellent Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6-7m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1215 Thinner Packaging : 1, 4, 20L To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : Refer to Technical Data Sheet. Pot Life : 1 - 2 days art 25°C (Refer to Technica Datasheet). Thinning : Thin up to 25% with MIROSOL 1294 (Medium Thinner) - (Refer to Technica Datasheet). Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use. Domestic & commercial furniture, wardrobes, kitchen cupboards and doors. Read More

Code: 3606 Low odour, low formaldehyde, isocyanate-free, clear acid-catalysed topcoat with a long pot life, suitable for interior wood. Features: Fast drying rate and long pot life make it ideal for automatic line operations Results in a tough resilient film that protects quality furniture and fittings. High build, provides maximum build with the minimum number of coats applied Low yellowing, ideally suited for application over blond timbers and liming stains Low formaldehyde, provides a safer working environment for persons applying the coatings, and compared to conventional acid catalysed coatings, superior in-service air quality around the coated article Specifications: Colour : Clear Finish : Matt (10%), Satin (30%), Semi Gloss (60%) & Full Gloss Build : Excellent Sandability : Excellent Vertical Hold Up : Excellent Solvent Resistance : Good Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6-7m2 per litre at 150 micron wet film build. This is dependent on the application equipment/gun set up and the article being coated Dry Time : Refer to Technical Datasheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : 10 Parts MIROBILD AC 3606 Part A + 1 Part MIROBILD AC 3800 Universal Catalyst or MIROBILD AC 3810 Quick Dry Catalyst by volume. Mix A & B and then add thinner. Allow mixed product to stand for 15 minutes prior to thinning, this will ensure that maximum film hardness and clarity is obtained. Failure to allow time for reaction to take place may result in a hazy film. Pot Life : 1-2 days at 25°C Pot life varies significantly with ambient temperature, humdity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. Thinning : Thin up to 30% with MIROSOL 1220, 1222 (Fast), 1294 (Medium), 1242 (Slow). In hot or draughty conditions up to 10% MIROSOL 1218 Ultra Slow Thinner may be added. Do not exceed 10% addition as it will retard the drying and could lead to problems with sanding, printing and blocking. Use faster thinners to achieve the required viscosity and then use (only if required) a small amount of MIROSOL 1218 to improve flow and levelling. In damp, cool or high humidity conditions, up to 10% MIROSOL 1297 Retarder may be added to help prevent blushing (a milkiness or haze in the film). Heating the application environment e.g. warming with infra-red lamps and avoid spraying early in the morning and late evening when temperatures are at their coldest, will also help to reduce the risk. Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi) Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Curtain Coating - Viscosity 40-50 seconds. Where To Use: Interior use only. Domestic and commercial furniture, wall panelling, joinery and fixtures. Read More

Code: 3810 Quick dry catalyst for use with MIROBILD AC Acid Catalysed coatings. To View Tech Data Sheet and Safety Data Sheet: Register To View Read More

Code: 3622 High build, fast drying, easy sanding, clear acid catalysed sealer. Specifically formulated to provide sound adhesion to DAP and vinyl coated board (commonly used in the casket industry). Features: Fast drying rate and long pot life make it ideal for automatic line operations High build, ensures a full finish when topcoated Excellent sanding reducing sanding time Specifications: Colour : Milky in can, dries clear Build : Excellent Sandability :Excellent Vertical Hold Up : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6-7m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Datasheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : Best adhesion, best gloss hold up and faster cure at low temperatures e.g. below 20°C: 10 Parts MIROBILD AC 3622 Part A + 1 Part MIROBILD AC 3800 Universal Catalyst or MIROBILD AC 3810 Quick Dry Catalyst by volume. For extended pot life, especially at high temperatures e.g. above 30°C 20 Parts MIROBILD AC 3622 Part A + 1 Part MIROBILD AC 3800 Universal Catalyst or MIROBILD AC 3810 Quick Dry Catalyst by volume. Mix A & B and then add thinner. Allow mixed product to stand for 15 minutes prior to thinning, this will ensure that maximum film hardness and clarity is obtained. Failure to allow time for reaction to take place may result in a hazy film. Pot Life : 1-2 days at 25°C Pot life varies significantly with ambient temperature, humdity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. Thinning : Thin 10-15% with MIROSOL 1220 (Fast), 1294 (Medium), 1242 (Slow) In hot or draughty conditions up to 10% MIROSOL 1218 Ultra Slow Thinner may be added. Do not exceed 10% addition as it will retard the drying and could lead to problems with sanding, printing and blocking. Use faster thinners to achieve the required viscosity and then use (only if required) a small amount of MIROSOL 1218 to improve flow and levelling. In damp, cool or high humidity conditions, up to 10% MIROSOL 1297 Retarder may be added to help prevent blushing (a milkiness or haze in the film). Heating the application environment e.g. warming with infra-red lamps and avoid spraying early in the morning and late evening when temperatures are at their coldest, will also help to reduce the risk. Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Curtain Coating - Viscosity 40-50 seconds. Where To Use: Interior use only. Domestic and commercial furniture, caskets. Read More

Code: 3720 A high build, free sanding undercoat for use on wood, medium density fibreboard (MDF) or particleboard. Ease of sanding makes for faster throughput in a production situation. Features: High build, enhances the finished appearance of the topcoat and can be applied directly over MDF to seal the fibres Easy to sand Excess MIROBILD AC 3770 topcoat may be added into MIROBILD AC 3720 undercoat to create a tinted undercoat. This improves coverage and reduces waster of topcoat Specifications: Colour : White Finish : N/A Build : Excellent Sandability : Excellent Vertical Hold Up : Excellent Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6-7m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner To View Tech Data Sheet: Register To View Application: Mixing Ratio (by volume) : 10 Parts MIROBILD AC 3720 Part A + 1 Part MIROBILD AC 3800 Universal Catalyst or MIROBILD AC 3810 Quick Dry Catalyst by volume. Mix A & B and then add thinner. Allow mixed product to stand for 15 minutes prior to thinning, this will ensure that maximum film hardness and clarity is obtained. Failure to allow time for reaction to take place may result in a hazy film. Pot Life : 1 day at 25°C Pot life varies significantly with ambient temperature, humdity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. Thinning : Thin up to 20% with MIROSOL 1220 (Fast), 1294 (Medium), 1242 (Slow) In hot or draughty conditions up to 10% MIROSOL 1218 Ultra Slow Thinner may be added. Do not exceed 10% addition as it will retard the drying and could lead to problems with sanding, printing and blocking. Use faster thinners to achieve the required viscosity and then use (only if required) a small amount of MIROSOL 1218 to improve flow and levelling. In damp, cool or high humidity conditions, up to 10% MIROSOL 1297 Retarder may be added to help prevent blushing (a milkiness or haze in the film). Heating the application environment e.g. warming with infra-red lamps and avoid spraying early in the morning and late evening when temperatures are at their coldest, will also help to reduce the risk. Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Curtain Coating - Viscosity 40-50 seconds. Where To Use: Interior only. Domestic & commercial furniture, wardrobes, joinery and fixtures. Read More