MIROTEC WB Water Based Coatings

Code: 8060 Clear, single pack, water based topcoat. It is easy to apply and low yellowing. Features: Single pack, no pot life issues to manage and less waste of product Water white and low yellowing, it is ideal for use over blonde timbers and liming stains To minimise the risk of sink back and tannin bleed and achieve the best possible water and chemical resistance, apply MIROTHANE PU 5500 Clear Isolator mixed 10A:1B with MIROTHANE PU 5789 Hardener, as a first coat on bare wood Higher solids content than clear nitrocellulose and precatalysed lacquers with similar chemical resistance to clear precatalysed lacquers. Low VOC (solvent content), non-flammable, low odour, safer for workers and the environment Formaldehyde free, zero formaldehyde emissions in rooms in which coated articles are installed or used Isocyanate free, does not require air assisted face masks or other respiratory personal protective equipment for application Phthalate free, it is ideal for children’s toys Complies with the Green Building Council Australia: Green Star – Office Design v3 & Office As Built, Table IEQ-13.1 Maximum TVOC Content Limits for Paints, Varnishes and Protective Coatings Specifications: Colour : Clear Finish : Matt (10%), Satin (30%) & Semi Gloss (60%) Build : Good Sandability : Excellent Vertical Hold Up : Very Good Solvent Resistance : Good Water Resistance : Good Levelling & Flow : Excellent Sink Back : Minimal Coverage : 7m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment with water following use. Refer to Technical Data Sheet for further information To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Thinning : Thin 10-15% with water depending upon application requirements. In cold conditions or when a faster dry time is required, MIROSTAIN 2101 Clear Tint Base (CTB) may be used to thin MIROTEC WB 8060. Note: only thin the volume of MIROTEC WB 8060 required for the job at hand. Once thinned the viscosity will continue to fall during the next 24 hours. If the application viscosity is too low, mix with some unthinned MIROTEC WB 8060 to bring the viscosity back up to the target. Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use only. Ideal for domestic and commercial furniture, children’s toys and furniture, picture frames, musical instruments, joinery and antique restoration. Read More

Code: 8022 Clear, single pack, water based sealer that is easy to apply, low yellowing and easy to sand. Features: Single pack, no pot life issues to manage and less waste of product Easy to sand, powders easily ensuring the quickest time to sand Water white and low yellowing, it is ideal for use over blonde timbers and liming stain Good build, to further minimise the risk of sink back and tannin bleed, apply MIROTHANE PU 5500 Clear Isolator as a first coat on bare wood Low VOC (solvent content), non flammable, low odour, safer for workers and the environment Formaldehyde free, zero formaldehyde emissions in rooms in which coated articles are installed or used Isocyanate free, does not require air assisted face masks or other respiratory personal protective equipment for application Pthalate free, it is ideal for children’s toys Complies with Green Building Council Australia: Green Star – Office Design v3 & Office As Built, Table IEQ-13.1 Maximum TVOC Content Limits for Paints, Varnishes and Protective Coatings Specifications: Colour : Clear Build : Good Sandability : Excellent: Vertical Hold Up : Very Good Solvent Resistance : Good Water Resistance : Good Levelling & Flow : Excellent Sink Back : Minimal Coverage : 7m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment with water following use To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Thinning : Supplied ready for use (RFU). However if required, it may be thinned with up to 5% water depending upon application requirements. Note: only thin the volume of MIROTEC WB 8022 required for the job at hand. Once thinned the viscosity will continue to fall during the next 24 hours. If the application viscosity is too low, mix with some unthinned MIROTEC WB 8022 to bring the viscosity back up to the target. Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use only. Ideal for domestic and commercial furniture, children’s toys and furniture, picture frames, musical instruments, joinery and antique restoration. Read More

Code: 8126 A pigmented, single pack, water based undercoat that may be applied by spray, it is especially suited for application on automatic lines. Features: Single pack, no pot life issues to manage and less waste of product. Excellent sanding, powders easily. Low VOC (solvent content), non-flammable, low odour safer for workers and the environment. Complies with the Green Building Council Australia: Green Star - Office Design v3 & Office As Built, Table IEQ-13.1 Maximum TVOC Content Limits for Paints, Varnishes and Protective Coatings. Mould resistant, contains fungal biocides for in-can stability and protection against discolouration from fungal / mould stains once applied. Specifications: Build: Good Sandability: Excellent Vertical Hold-Up: Very Good Solvent Resistance: Good Water Resistance: Excellent Levelling & Flow: Excellent Sink Back: Minimal Colour: White Coverage: 10m2 per litre at 100 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated. Dry Time: Dust Free: 8-12 minutes  Touch Dry: 10-15 minutes  Sanding: 30-40 minutes   Block Stacking: 24 hours To View Tech Data Sheet and Safety Data Sheet: Register To View Read More