MIROKEY Etch Primers

Code: 1012-6615-2158 Grey etch primer. To View Tech Data Sheet and Safety Data Sheet: Register To View Read More

Code: 6615 High performance, zinc phosphate etch primer specifically designed for direct application over mild steel, zinc-anneal, chrome, brass, lead and lead alloys, stainless steel, aluminium and galvanised iron. Features: Excellent adhesion to a variety of cleaned metal surfaces Single pack, easy to use Contains zinc phosphate, proven corrosion resistance Fast drying Specifications: Colour : White or Grey Build : Good Vertical Hold Up : Excellent Solvent Resistance : Dependent on topcoat Water Resistance : Very Good Levelling & Flow : Very Good Sink Back : Minimal Coverage : 7-10m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1234 or 1286 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Thinning : Thin 5 to 15% with MIROSOL 1234 or 1286 Fast or 1294 Medium Thinner. Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Metal fabrication, box trailers, caravans, safes, plant & machinery, farming equipment, earth moving equipment, skip bins and automotive. Read More

Code: 5629 A premium grade, high solids , low viscosity polyurethane primer for metal. Features: Easy to sand, poweders easily making it ideal for hand sanding High solids, low viscosity  provides superior build with minimal thinning Superior chemical and moisture resistance Fast drying properties ensure early recoat and faster shipping & handling times Specifications: Colour : White, black tinted Finish : N/A Build : Very High Sandability : Excellent Vertical Hold Up : Excellent Solvent Resistance : Excellent Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6 -7m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 Thinner Packaging : 4 -16L To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : 3 parts 5629 Part A + 1 part 5747 Part B (3A:1B) Pot Life : 2 hours at 25°C (refer to datasheet) Thinning : Thin up to 20% with MIROSOL 1217 (Fast), 1265 (Medium), 1266 (Slow), 1218 (Ultra Slow) Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior & exterior applications suitable for some automotive plastic & plastic parts, metal structural frames, machinery, caravans & earthmoving equipment. Read More